Do you have to screw the pedestals?

In principle, the outermost row of pedestals should be secured. Whether screwing them in place is possible depends on the terrace's condition. 1. What is the outermost row of pedestals? The outermost row of pedestals is the row adjacent to an open edge. An open edge is an edge that is not closed off by walls or fixed fixing brackets. A typical example of an 'open edge' is the last row adjacent to a balcony railing. 2. Why should the outermost row of pedestals be secured? The reason is to prevent any shifting of the outermost row of slabs. 3. How can they be secured? This depends on the condition of the substrate: On a concrete substrate, the pedestals can be screwed in place. On a waterproof membrane, the pedestals must be glued. Otherwise, the waterproof membrane will be damaged.

Does the movable head reduce the maximum breaking load compared to a fixed pedestal bearing?

Compared to a horizontal position of the pedestal head, the maximum load-bearing capacity is reduced by between 5% and 20% according to technical tests. This reduction results from an increased stress on one side of the outer static support structure of the pedestal in the case of a decentralized load.

What happens if a narrow edge plate rests on only two points of a self-leveling head? Will the head then tilt outwards unintentionally?

Yes, that can happen when full-surface slabs abut small edge slabs. The larger slab then levers the smaller one out. In such cases, you should convert the outer edge pedestals into a pedestal with a fixed head. With Easy Pro, this is done by using the fixing ring. This is inserted into the pedestal head and blocks the self-leveling mechanism. (See fixing ring.)

Are self-leveling systems suitable for roof terraces in exposed locations, or do fixed heads offer more stability against uplift forces?

Neither system offers any additional protection against extreme storms or tornadoes in their standard configuration. Should this be the case for a terrace, we recommend: a) bonding the pedestals to the ground; b) bonding the slabs to the pedestals. Both measures together lead to a significant improvement in resistance to wind-induced lifting. Alternatively, we recommend increasing the thickness of the slabs to be laid (e.g., from 2 cm to 3 cm).

Does the ball joint of the head tend to 'seize' or squeak after years of stress due to thermal expansion of the plates?

After selling over a million self-leveling pedestal bearings, we have not observed any signs of mechanical wear or acoustic impairment, even after years of use.

Can I use a self-leveling pedestal if both the subfloor has a slope and the slab surface is to have a (different) slope?

Yes, you can! A self-leveling pedestal can not only compensate for a slope but also create one. The following images illustrate an artificially created slope on a wooden substructure. This can also be applied to slab coverings.

Does dirt and water collect in the movable head, which could lead to frost damage in winter?

Here, a distinction must be made between dirt and water: a) Water: Yes, water can accumulate in the movable head (rarely) or a film of water can form (more frequently). In winter, this can lead to ice formation. This ice is then broken up by walking on it, and a slight cracking sound can be heard once. This 'frost cracking' is unavoidable in reality, as the most frequent cause is not direct water ingress but the formation of condensation. b) Dirt: Significant dirt accumulation in winter – and the associated impairment of the acoustics – has not occurred in a single case to date. We have not received any reports of this.

At what percentage gradient does the extra cost for a self-leveling system become worthwhile compared to leveling shims?

The additional cost for adjustable pedestals must be weighed against the significantly increased installation effort and the reduced installation accuracy. For example: a) The additional cost per square meter for self-leveling pedestals is approximately €7 to €12 compared to pedestals with a fixed head (including leveling shims). b) An installer charges €50 per square meter of installed area for installation only, excluding materials. Therefore, the installer should only incur additional work of 7/50 to 12/50 = 8,4 to 12 minutes per hour for installing fixed pedestals. This calculation does not take into account the reduced installation accuracy of fixed pedestals with leveling shims.

Can I combine EasyPro with rail systems, or is the movable head only useful for the direct installation of slabs?

You can use EasyPro with both the Slim Easy rail system and the Smart Wabic raised floor system. For example, with the Slim Easy rail system, the 4mm pedestal head fits the base profile exactly, as shown in the following image:

Does the system also compensate for unevenness in the screed or waterproofing (overlaps/dents/bumps), or is it intended purely for constant slopes?

The 5° mechanism reaches its limits with large overlaps or elevations. In these cases, additional measures are required, such as our 1mm and 3mm leveling washers which must be placed under the pedestal bearing.

Illustration of 3 laid slabs with the EasyPro pedestal supports

Self-leveling pedestal support EasyPro 6,7 – 15,4cm

Q: What is the difference between 'Professional' and 'EasyPro'

This is a very frequently asked question from our customers. Apart from the price, which is significantly lower for the 'EasyPro' series, we can provide you with some details in the following table: Criteria EasyPro Professional Load capacity up to 1,3 tons per unit up to 1,6 tons per unit Base Closed base (more even weight distribution) Partially open Number of base pedestals 42 Number of different adapters 12 Fixing function Available as an accessory Standard integrated Anti-slip pad Integrated 2mm joint available Yes Yes 4mm joint available Yes Yes Edge cladding mountable Yes Yes Edge profile mountable Yes Yes Upper and lower riser clips for 2cm cladding available Yes Yes Upper and lower riser clips for 3cm cladding available Yes No

Adjustment range:	6,7 to 15,4 cm
joint thickness:	2mm, 4mm
Item number:	SLSP67157E

Reviewed with 4.91 from 5, based on 80 Customer Reviews

(81 Customer Reviews)

5,39 € pc.

VAT included excl. Shipping costs

new professional pedestal supports for the adjustment range 6,7 to 15,4 cm
for wooden decking – automatically compensates for gradients of up to 5%
joint thickness 2 or 4 mm | can be separated individually
Extremely resilient – Breaking load per pedestal up to 1,3 tons
including anti-acoustic and anti-slip pad
low load on any existing insulation layer by large support surface
for porcelain stoneware (tiles) with a thickness of 2 cm and 3 cm as well as natural and concrete stone slabs up to 6 cm thick

TOP prices - from the 1st piece!

joint thickness:

Quantity	Price
1 - 191 pc.	5,39 €
192+ pc.	5,12 €

✓ FREE SHIPPING for orders from 250€ (only in AT and DE)
✓ Planning with 3D configurator
✓ 100% recyclable
✓ 10 years warranty
✓ weatherproof
✓ UV-resistant

Shipping type: cardboard itemsMore about shipping costs

The EasyPro 6,7-15,4cm self-leveling pedestal allows you to precisely lay terraces with a automatic gradient compensation up to 5°. For medium installation heights, the EasyPro system (6,7 – 15,4 cm) offers maximum flexibility and particularly time-saving installation of your patio slabs thanks to its integrated double thread.

Self-leveling pedestal
Excellent resilience
2mm or 4mm joint
Double internal thread for maximum adjustment range

Illustration of a terrace with a sloping edge

EasyPro self-leveling pedestal supports – advantages at a glance

Efficient product range: Only four basic types cover the entire adjustment range from 2,8 cm to 40,5 cm. This allows for more efficient assembly and drastically reduces the risk of incorrect orders.
Joints 2mm or 4mmWhether you prefer slim 2mm joints or robust 4mm joints: there's something for everyone!
Double thread: This pedestal support is equipped with an internal double thread to compensate for large differences in height.
In the image, (3) and (4) show the internal double thread.

(1) = Adjustment wrench (optional)
(2) = Joint head (for 2mm and 4mm joints) – included in the delivery
(3) + (4) = internal double thread
(5) = Locking ring for threads – secures the thread position
(6) = Pedestal base
Easy height adjustment: You adjust the height intuitively using the adjustment key (left) or the adjustment ring (right).
Full footprint: The load is transferred into the subsoil across the entire base.
Integrated anti-slip and anti-acoustic padding: These soft and damping pads are integrated as standard into every pedestal head for slabs.
Maximum durability: The system is weatherproof and temperature resistant from -40 °C to +80 °C.
Automatic balancing: The self-leveling system automatically compensates for uneven ground up to +/- 5°.
Versatile accessories: A comprehensive program offers solutions for almost every construction challenge.

Explanation of the system

The heart of the EasyPro 6,7-15,4cm self-leveling pedestal is the movable head.
As soon as you place the slabs on the support, the movable head attempts to balance all the slabs. Since the weight of each slab is essentially the same (e.g., four adjacent 60x60 slabs resting at one corner on a movable pedestal head), the movable head will find equilibrium and move into a horizontal position. This is similar to an old kitchen scale. When the weight on the left and right sides is equal, the movable middle section automatically returns to the horizontal position.
Illustration of a scale with EasyPro pedestal bearing

The most important system accessory – EasyPro self-leveling pedestal supports 6,7-15,4cm

Accessories extend the functionality of the EasyPro system and solve complex details at edges and transitions.
For all EasyPro system accessories

1. The edge finishing clip

This Plastic clip It serves as a lateral edge against adjacent masonry. The clip securely clamps the panel, preventing slippage and simultaneously protecting the wall.

2. The adjustment key

Our preview of this tool You can easily adjust the height of the pedestal during installation.
The key is simply inserted into the central mounting slot.

3. Vertical edge finish

For visually appealing visible edges, choose between Edge cladding panels made of aluminum edge cladding or Stainless steel clips for risers.
Shown here are the edge trims on the left and the edge panels on the right:

Regarding edge finishing solutions

4. Fixing ring

Narrow edge plates can cause plates to be levered out.
The Fixing ring This transforms the bearing into a pedestal bearing with a fixed head in a matter of seconds.

5. Drainage solutions

The system is compatible with professional drainage channels to effectively prevent standing water on the terrace surface.
The following example shows the Rain Grid drainage cover.

To the drainage channels

Assembly: Step-by-step instructions

Installation proceeds in logical steps. We recommend that you first create a mounting jig from wood or aluminum that exactly matches the length of your panels.

1. Cutting the edge bearings

Position the pedestals as close as possible to the outer edge. To avoid overhangs, trim the base of the pedestal along the pre-marked cut lines on the underside using a jigsaw. The following image shows a pedestal trimmed on one side in the middle and a pedestal trimmed on both sides on the right.
Cutting the EasyPro pedestal supports and showing the cut-off pedestal supports

2. Positioning and alignment

Set up the (trimmed) edge supports and the first inner row.
Use the mounting template for the distances and a spirit level (at least 2 m) to adjust the desired level using the rotary ring or the adjustment key.
Next, attach the edge clips.
Illustration of the installation of the first rows of pedestals using the EasyPro self-leveling pedestal system.

3. Laying the slabs

Before laying the first slab, you should break off the unnecessary joint spacers so that it lies flush against the edge.
Please also check the level regularly with a spirit level.
Then continue laying the pedestals and slabs until you reach the edge area.

Laying the first rows of EasyPro panels

4. Vertical edge finish

For a vertical edge finish – if required – you have several options:

an aluminum edge trim (image left) in the standard version or in the 'Sideline' version
the edge trim (in the picture on the right)
a version with upper and lower riser clips (image below)

Illustration of the edge finishes for self-leveling pedestal supports EasyPro
Illustration of individual parts and assembled upper and lower riser clips for self-leveling pedestals EasyPro

Regarding edge finishing solutions

Planning via the configurator

Avoid costly mistakes and plan your project with utmost precision. Our free online configurator automatically calculates the required number of pedestals and the perfect accessories for your terrace. It can be used anonymously and without registration.

3D terrace configurator for EasyPro pedestal systems

View configurator

Scope and system

The EasyPro system is optimized for porcelain stoneware, natural stone, and concrete pavers. It is ideally suited for classic terrace constructions as well as for our 'Slim Easy' rail system and our 'Smart Wabic' raised floor system. Thanks to the option of converting to a fixed head, it is particularly flexible for use near house walls and with narrow slab strips.

Technical specifications: Self-leveling pedestal support EasyPro 6,7-15,4cm

Here are the technical specifications of the EasyPro pedestal system:

Property	Details
Material	Polypropylene (PP), 100% recyclable
Adjustment option	Adjustment ring, adjustment wrench
Capacity	max 1.300 kg per bearing (laboratory breaking load)
Temperature range	-40 ° C to +80 ° C
Height of pedestal supports	6,7 cm - 15,4 cm
joint width	Selectable 2 mm or 4 mm
joint height	1 cm
Compatibility	Slim Easy rail system, Smart Wabic raised floor
Peculiarity	Included anti-slip and anti-acoustic pads
Guarantee	10 years

The following table shows the installation heights for the EasyPro model (range 6,7 to 15,4 cm).
The installation height is the distance from the ground surface to the top edge of the new terrace covering.

Type of covering (example)	Minimum building height (H1)	Maximum building height (H2)
Porcelain stoneware (2 cm thick)	8,7 cm	17,4 cm
Natural stone (3 cm thick)	9,7 cm	18,4 cm
Concrete block (4 cm thick)	10,7 cm	19,4 cm
Concrete block (5 cm thick)	11,7 cm	20,4 cm

Representation of the installation height of a pedestal support construction

Delivery

You will receive the "EasyPro" adjustable pedestal in the selected adjustment range, including pre-assembled joint spacers. Please order accessories such as fixing rings, edge clips, adjustment keys, and drainage components separately according to your individual requirements.

Planning notes / Material requirements

For narrow slabs (14 cm and above), be sure to use fixing rings. Use the installation jig to save time on large areas and achieve precise joint patterns. Ensure that the pedestal base for the edge trim is cut exactly 3 mm above the outer perforation.

Care / Maintenance of the EasyPro self-leveling pedestal system

The system is maintenance-free and durable. We simply recommend regularly checking the joints for dirt. This ensures that rainwater can drain away freely and that the drainage function of the substructure is maintained.

EasyPro Sample Sets

You are welcome to order our 'Medium' or 'Large' sample set in advance to experience the quality and ease of use firsthand. Clicking on the image will take you directly to the sample sets.

Sample set Medium EasyPro, adjustment range 6,7 to 15,4 cm with 2 mm gap Sample set X-Large EasyPro, adjustment range 6,7 to 15,4 cm with 2 mm gap

Frequently Asked Questions about EasyPro

What is the difference between 'Professional' and 'EasyPro'

This is a very common question asked by our customers.
Apart from the price, which is the case with the 'EasyPro' series much lower We can provide you with some details using the following table:

Gemini pedestal in the adjustment range 6,7 to 15,7cm with joint 2mm

Professional pedestal 8,8 to 11,8 cm joint 2mm

Criteria	EasyPro	Professional
Capacity	up to 1,3 tons per piece	up to 1,6 tons per piece
Base	closed base (more even weight distribution)	partially open
number of base supports	4	2
number of different adapters	1	2
fixation function	available as an accessory	installed as standard
Anti-slip pad	integrated	integrated
joint 2mm available	ja	ja
joint 4mm available	ja	ja
edge panel mountable	ja	ja
edge profile mountable	ja	ja
Upper and lower riser clips for Wide base-Cover available	ja	ja
Upper and lower riser clips for Wide base-Cover available	ja	no

Do you have to screw the pedestals?

In principle, the outermost row of pedestals should be fixed..
If a screw connection is possible depends on the terrace condition

1. What is the outermost row of pedestals?

The outermost row of pedestals is a row to an open edge. An open edge is an edge that is not enclosed by walls or fixed fixing angles.

A typical 'open edge' is the last row of a balcony railing.

2. Why should the outermost row of pedestals be fixed?

The reason is that there should be no shifts in the outermost row of plates.

3. How can the fixation be done?

This depends on the nature of the subfloor:

On a concrete subfloor the pedestal can be screwed in. .
On a sealing layer the pedestal must be glued to the layer. Otherwise, the sealing layer will be damaged.
Does the movable head reduce the maximum breaking load compared to a fixed pedestal bearing?

Compared to a horizontal position of the pedestal head, the maximum load-bearing capacity is reduced by between 5% and 20% according to technical tests carried out.
This decrease results from an increased stress on one side of the outer static support structure of the pedestal bearings – in the case of a decentralized load.
What happens if a narrow edge plate rests on only two points of a self-leveling head? Will the head then tilt outwards unintentionally?

Yes, that can happen when full-surface slabs abut small edge slabs.
The larger plate then levers the smaller plate out.

In such cases, you should convert the outer edge pedestals into a pedestal with a fixed head.
This is achieved with Easy Pro through the use of the fixing ring.
This is inserted into the pedestal head and blocks the self-leveling mechanism.

To the fixation ring
Are self-leveling systems suitable for roof terraces in exposed locations, or do fixed heads offer more stability against uplift forces?

Neither. Neither system offers any additional protection against extreme storms or tornadoes as standard.
If this is the case for a terrace, we recommend:
a) the bonding of the pedestals to the floor
b) the bonding of the slabs to the pedestals

Both measures together lead to a significant improvement in protection against uplift wind forces.
Alternatively, we recommend increasing the thickness of the slabs to be laid (e.g. from 2cm to 3cm).
Does the ball joint of the head tend to 'seize' or squeak after years of stress due to thermal expansion of the plates?

After selling over a million self-leveling pedestal bearings, we have not observed any signs of mechanical wear or acoustic impairment, even after years of use.
Can I use a self-leveling pedestal if both the subfloor has a slope and the slab surface is to have a (different) slope?

Yes, you can! A self-leveling pedestal can not only compensate for a slope but also create a different slope.
The following images illustrate an artificially created slope in a wooden substructure. This can also be applied to slab coverings.
Does dirt and water collect in the movable head, which could lead to frost damage in winter?

Here, a distinction must be made between dirt and water:

a) Water
Yes, water can accumulate in the movable head (rarely) or a film of water can form (more frequently). In winter, this can lead to ice formation. This ice is then broken up by walking on it, and a slight cracking sound can be heard once. This 'frost cracking' is unavoidable in reality.
Because the most common cause is not direct water ingress but the formation of condensation.

b) dirt
Significant dirt accumulation during winter – and the associated impairment of acoustics – has not occurred in a single instance to date. No reports of such occurrences have been received from us.
At what percentage gradient does the extra cost for a self-leveling system become worthwhile compared to leveling shims?

The additional cost for the pedestal supports must be weighed against the significantly increased installation effort and the reduced installation accuracy. For example:
a) The additional cost per m² for self-leveling pedestals is approximately EUR 7 to 12 compared to pedestals with a fixed head (including leveling washers).
b) A publisher charges EUR 50.-/m2 of laid area only for the laying, excluding material.
The installer may therefore only incur additional costs of 7/50 to 12/50 = 8,4 minutes to 12 minutes per hour for the installation of fixed pedestals.
This does not include the lower installation accuracy of fixed pedestals with leveling discs.
Can I combine EasyPro with rail systems, or is the movable head only useful for the direct installation of slabs?

You can use EasyPro for both the Slim Easy rail system and the Smart Wabic raised floor system.
For example, in the Slim Easy rail system, the 4mm pedestal bearing head precisely accommodates the base profile, as can be seen in the following image:
Does the system also compensate for unevenness in the screed or waterproofing (overlaps/dents/bumps), or is it intended purely for constant slopes?

The 5° mechanism reaches its limits in cases of large overlaps or elevations.
Additional measures are then required, e.g. our 1mm- and 3mm leveling discs which are to be placed under the pedestal support.

All variants of the EasyPro series compared

Here you can see an overview of all types in the EasyPro series:

designation	Verstellbereich	Item No. (SKU)	Link
EasyPro pedestal support	2,8 - 3,6 cm	SLSP2836E	VIEW SURVEY NOW
EasyPro pedestal support	3,5 - 6,7 cm	SLSP3368E	VIEW SURVEY NOW
EasyPro pedestal support	6,7 - 15,4 cm	SLSP67157E
EasyPro pedestal support	15,5 - 40,5 cm	SLSP154405E	VIEW SURVEY NOW

Adjustment range of the pedestal 6,7 to 15,4cm

	Minimum construction height H1	Maximum construction height H2
Porcelain stoneware with Thickness 2cm	8,7	17,4
Porcelain stoneware / natural stone with Thickness 3cm	9,7	18,4
Natural or concrete stone with Thickness 4cm	10,7	19,4
Natural or concrete stone with Thickness 5cm	11,7	20,4

Example calculation: Minimum adjustment range 2,3cm + ceramic 2cm = Minimum height H1 : 4,3cm

height adjustment options

The 'Gemini' pedestal supports have the following height adjustment options:
(a) using an adjustment key
(b) by means of a rotating ring

(a) Height adjustment using adjustment key

With the adjustment key, our Gemini pedestals can be quickly adjusted to the required height.
The large slot in the Gemini pedestal supports accommodates the adjustment key and enables its perfect hold!

The key is used exclusively for height adjustment without plates in place.
The fine adjustment of the height of already laid panels is done using the large adjustment rings, which are built directly into the 'Gemini' pedestal supports!

(b) Height adjustment using adjustment ring

All pedestal supports in the 'Gemini' series have integrated swivel rings which allow the height of the pedestal supports to be perfectly adjusted.
These are easy to operate by hand.

The two height adjustment options of EasyPro

Conversion to a pedestal with fixed head (non-self-leveling)

By using our fixation ring You can

within seconds
block the self-leveling mechanism permanently and stably!

This converts the self-levelling pedestal support 'EasyPro' into a pedestal support with a fixed head

To the fixation ring

Why do we offer you this option?

For pedestal constructions With the 'EasyPro' pedestal support, situations regularly arise where narrow edge panels must be installed. Under certain circumstances, this can cause the edge panels to tilt slightly due to significant weight differences.

Negative effects of unfixed pedestals at the edge

Within the rail system construction Our system 'Slim Easy' will help you with this conversion

the easier installation of the first, outermost base profile (movement of the base profile is prevented and height adjustment is thus made much easier)
increasing edge stability

Height adjustment of the pedestal bearings using a rotating ring

Installation of the fixation ring

The assembly takes place in two quick steps, which are completed within seconds:

First, the fixing ring is inserted into the pedestal head:
Then the head with the fixing ring is inserted into the pedestal base – done!

First assembly step of installing the fixing ring into the EasyPro pedestal bearing

Second assembly step of installing the fixing ring into the EasyPro pedestal bearing

Arrangement of pedestals for narrow edge areas

You can easily solve narrow edge areas from a width of 14cm with the 'EasyPro' pedestal support.

There are a few steps you need to complete

Cutting the pedestal supports and partially cutting off the joint heads
Inserting the fixation ring
if necessary, gluing the panels

(1) Cutting the pedestals

For narrow edge areas it is necessary to reduce the size of the pedestals.
This is also easily possible: you can reduce the size of the pedestal support along the pre-punched cutting lines on the underside. You can see the dashed lines below

Using a jigsaw, you can then cut the pedestal support

There are four ways you can reduce the size of the 'EasyPro' pedestal support:
– one-sided cutting
– two-sided cutting
– two-sided, right-angled cut
– all-round cutting

possible cutting types Pedestal bearing Gemini

(2) Installation of the fixing ring

In order to prevent tipping of narrow edge panels, the outermost pedestals should be converted into pedestals with a fixed head using the fixing ring for safety reasons.

To the fixation ring

The assembly takes place in two quick steps, which are completed within seconds:
First, the fixing ring is inserted into the pedestal head:

Installation step 1 of the fixing ring for the Gemini pedestal

Then the head with the fixing ring is inserted into the pedestal base – done!

Installation step 2 of the fixing ring for the Gemini pedestal

(3) Installation situations

You can now see the installation situations for narrow edge panels.
For better clarity, only the pedestal supports are shown without any edge finishing clips that may be used.

(3.1) The minimal variant: width 14cm

Here you see the version with a minimum panel width of 14cm.
The top row, consisting of 6 pieces, must be cut off on four sides, all joint tabs must be removed and the fixing rings must be installed

Arrangement of pedestal supports Gemini with narrow edge plates at 14cm

(3.2) Variant: Width between 14cm and 22cm

The structure is analogous to point 3.1. – only with further spacing.

Arrangement of pedestal supports Gemini with narrow edge plates at 18cm

(3.3) Variant: Width greater than or equal to 21cm

Arrangement of pedestal supports Gemini for narrow edge panels over 21cm

The vertical edge finish at EasyPro

With the EasyPro pedestal system, you can choose from the following different types of vertical edge finishes:

is edge cladding made of powder-coated aluminum
In Edge finish 'Sideline'
the edge profiles
the edge veneer made of powder-coated aluminum
the upper and lower riser connection clips Stainless steel

The edge cladding The pedestal is placed on top of the support, and the panel is then laid on top of that. The edge trim can also be glued or screwed to the support.

The edge trim is available in heights of 6cm, 8cm, 10cm, 12cm, 14cm, 16cm and 16cm.

The following colors are available in a matte finish:
Anthracite / Light beige / Light grey.

The system is suitable exclusively for 2cm thick paving slabs.

More information can be found at the following link:

To the edge panels

Mounted edge trim Sideline on EasyPro pedestal

The 'Sideline' edge finish This is a new way to create a cost-effective, elegant terrace edge finish.

This edge solution is available in heights of 6 cm, 8 cm, 10 cm and 12 cm.

Color: Anthracite matt.
The system is suitable exclusively for 2cm thick paving slabs.

More information can be found at the following link:

For the edge finish, 'Sideline'

The edge profiles (shown in the photo with pedestal supports 'Professional') are the first way to clad different vertical terrace heights.

Edge termination of raised floor, open edge, different heights

The following colors are available in a matte finish:
Anthracite / Light beige / Light grey.
The system is suitable exclusively for 2cm thick paving slabs.
More information can be found at the following link:

To the edge profiles

Almost finished construction of the edge trim with the panels

The edge veneer This is the second option, to vertically blend different lateral levels.

Suitable for 2cm slabs, it represents an elegant and technically sophisticated solution for perfectly designing the lateral edge of the terrace.

The following colors are available in a matte finish:
Anthracite / Light beige / Light grey.

More information can be found at the following link:

To the edge cladding

The upper and lower clips made of stainless steel This is the third option for vertically cladding different lateral levels.

At the same time, this terrace edge finish
there is best Edge solution and
also available for 3cm slabs.

More information can be found at the following link:

Regarding the upper and lower riser clips

Return options if you order too many pedestal supports!

Save time, money, and effort – we take back unwanted pedestals and accessories from the 'EasyPro' series!

You can't estimate your needs exactly or want to order a little more for eventualities? A good idea!
We accept returns of unused pedestal supports within 2 months of the date of purchase.
The prerequisite, of course, is that we can sell them again.

This means: the pedestals

must not be dirty
must not show any signs of use (scratches on the surface or the like)
arrive undamaged

What is the maximum number of pedestal supports we can take back?

We take back a maximum of 10% of the ordered quantity per delivery item!

An example:
– You order 200 pieces with a height of 3,3-6,8 cm and 100 pieces with a height of 6,7-15,0 cm.
– We take back a maximum of: 20 pieces of height 3,3-6,8 cm and 10 pieces of height 6,7-15,0 cm.

Return of accessories of the 'EasyPro' pedestal series:

We also take back accessories that are no longer needed – up to a maximum of 10% of the ordered quantity.
This only applies to the following articles:

– EasyPro edge trim clips
– Edge finishing clip for all pedestal types
– building protection pads

How is the return processed?

The return is made via our return center

Please register your return with us at the returns center.
Here you will find out
– which items you can return to us and in what quantity
– how much the expected refund amount will be.
– all information about the refund and
– to which address you should send the goods.

To the return center

How and when will the refund be made?

within 2 working days of delivery to us.
using the payment method you chose when making your purchase – more information can be found in the Returns Center.

Are manipulation costs deducted?

Yes, costs will be deducted - however, these are small and amount to 5% of the value of the goods, but at least EUR 9. These costs are below our cost price and represent only a part of the effort that would be required for the entire processing of a returns process.

81 reviews for Self-leveling pedestal support EasyPro 6,7 – 15,4cm

Reviewed with 5 of 5

Heiko July 5, 2026

Very good quality and reliable delivery

Verified purchase. More information
Reviewed with 5 of 5

Anonym June 19, 2026

Verified purchase. More information
Reviewed with 5 of 5

Helga Ehinger-Persico 16 May 2026

Verified purchase. More information
Reviewed with 5 of 5

Manfred Kreuzer April 25, 2026

Verified purchase. More information
Reviewed with 5 of 5

THOMAS April 24, 2026

Verified purchase. More information
Reviewed with 4 of 5

Philipp U. April 23, 2026

Verified purchase. More information
Reviewed with 5 of 5

Manfred Kreuzer April 18, 2026

Verified purchase. More information
Reviewed with 5 of 5

Ingrid March 20, 2026

It's great to work with.

Verified purchase. More information
Reviewed with 5 of 5

Detlef Fricke March 14, 2026

Verified purchase. More information
Reviewed with 5 of 5

Beata W. 8 December 2025

Very fast delivery and very good stilts. Unfortunately, we ordered the wrong size, but the exchange was straightforward, and the contact and advice were very friendly and competent. Thank you again!

Verified purchase. More information
Reviewed with 5 of 5

Othmar PEISCHL 29 November 2025

Verified purchase. More information
Reviewed with 5 of 5

John B 26 November 2025

Verified purchase. More information
Reviewed with 5 of 5

Mario Schabauer 24 November 2025

Verified purchase. More information
Reviewed with 5 of 5

Anonym 14 November 2025

Top

Verified purchase. More information
Reviewed with 5 of 5

Othmar PEISCHL 13 November 2025

Verified purchase. More information
Reviewed with 5 of 5

Adalbert Miesbauer 26 October 2025

Verified purchase. More information
Reviewed with 5 of 5

Detlev Herzog 17 October 2025

Verified purchase. More information
Reviewed with 5 of 5

Felix S September 16, 2025

Verified purchase. More information
Reviewed with 5 of 5

Anonym September 14, 2025

Verified purchase. More information
Reviewed with 5 of 5

Oliver G. September 1, 2025

Ceratrend's stilt supports are top-quality, easily adjustable, and very stable. A perfect solution for quick and clean patio installation – highly recommended!

Verified purchase. More information
Reviewed with 5 of 5

Horst V. August 17, 2025

Fast delivery (2 days from Austria) Great product

Verified purchase. More information
Reviewed with 5 of 5

Heribert K. August 15, 2025

Verified purchase. More information
Reviewed with 5 of 5

Stefanie August 10, 2025

Verified purchase. More information
Reviewed with 5 of 5

Margrit S. August 9, 2025

Verified purchase. More information
Reviewed with 5 of 5

Johann Hackl August 4, 2025

Excellent product, uncomplicated ordering and delivery process.

Not verified purchase. More information
Reviewed with 5 of 5

Manuel July 17, 2025

Verified purchase. More information
Reviewed with 5 of 5

Claudia L July 3, 2025

Verified purchase. More information
Reviewed with 5 of 5

Christian June 27, 2025

Easy to adjust

Verified purchase. More information
Reviewed with 4 of 5

Bernd June 23, 2025

Verified purchase. More information
Reviewed with 5 of 5

Ralph-Joachim Büttner June 2, 2025

I've rarely experienced such good and competent advice and top-notch customer service. Thanks to the team. This shop deserves more than 5 stars. This applies to all products. The quality is professional and first-class, very well made, robust, and valuable. All in all, highly recommended.

Verified purchase. More information
Reviewed with 5 of 5

Anonym 26 May 2025

Verified purchase. More information
Reviewed with 5 of 5

Thomas M 25 May 2025

Super stable pedestal. Top quality!

Verified purchase. More information
Reviewed with 5 of 5

Sebastian R. 11 May 2025

works simply and is very stable

Verified purchase. More information
Reviewed with 5 of 5

Robert M., Karlsruhe April 18, 2025

very good solid bearing

Not verified purchase. More information
Reviewed with 5 of 5

Heribert K, Vienna April 3, 2025

Good telephone advice and fast delivery. The product works very well. It's easy to install.

Not verified purchase. More information
Reviewed with 5 of 5

tim m., remagen March 9, 2025

perfect item, excellent

Not verified purchase. More information
Reviewed with 5 of 5

Jens R., Hamburg March 1, 2025

Very good bearing – double thread is top.

Not verified purchase. More information
Reviewed with 5 of 5

Thorsten H., Wismar 21 January 2025

top pedestal, fits perfectly under rail

Not verified purchase. More information
Reviewed with 5 of 5

heinz r., ludwigsburg 4 January 2025

For this price, the best self-leveling pedestal on the market. I'd be happy to use it again for my next projects.

Not verified purchase. More information
Reviewed with 5 of 5

Bernd Pühringer September 12, 2024

Verified purchase. More information
Reviewed with 5 of 5

Andrew H. September 6, 2024

Speedy delivery, good quality

Verified purchase. More information
Reviewed with 5 of 5

Jannis August 23, 2024

Great pedestal bearing, there is nothing comparable on the market that comes close to the quality of this bearing!

Verified purchase. More information
Reviewed with 5 of 5

Karl-Heinz B. July 4, 2024

Verified purchase. More information
Reviewed with 5 of 5

Dennis P. June 28, 2024

Great pedestal bearing, it's just fun to work with.

Verified purchase. More information
Reviewed with 5 of 5

Anonym June 26, 2024

Verified purchase. More information
Reviewed with 5 of 5

Thomas Karg June 24, 2024

Very good quality at an unbeatable price.

Verified purchase. More information
Reviewed with 4 of 5

Robert Welling-Knauff June 21, 2024

Verified purchase. More information
Reviewed with 5 of 5

Dominik June 20, 2024

Great product and fast delivery! We are extremely satisfied!

Verified purchase. More information
Reviewed with 5 of 5

ALFRED STEINDL June 17, 2024

Verified purchase. More information
Reviewed with 4 of 5

Alexander O. 29 May 2024

Verified purchase. More information
Reviewed with 5 of 5

Christopher M 4 May 2024

Top product, great service. Thank you 🙂

Verified purchase. More information
Reviewed with 5 of 5

Steffen 2 May 2024

Everything was perfect! Top service

Verified purchase. More information
Reviewed with 5 of 5

Andre Bennua April 13, 2024

Verified purchase. More information
Reviewed with 5 of 5

Valeri April 2, 2024

Verified purchase. More information
Reviewed with 5 of 5

Ewald Schwenner March 21, 2024

Great product, great, good price

Verified purchase. More information
Reviewed with 5 of 5

Jörg L., Wuppertal February 25, 2024

Excellent bearing – can be adjusted very well, just like the large bearing.

Not verified purchase. More information
Reviewed with 5 of 5

anonym February 9, 2024

everything OK

Not verified purchase. More information
Reviewed with 5 of 5

dirk l. ludwigsburg February 6, 2024

excellent system & good advice

Not verified purchase. More information
Reviewed with 5 of 5

Anonym 27 November 2023

Verified purchase. More information
Reviewed with 4 of 5

Gustav L., Frankfurt 17 November 2023

very good warehouse, solid, fast delivery - however, the parcel delivery person was unfriendly, so only 4 stars

Not verified purchase. More information
Reviewed with 5 of 5

Bianca Alvino 26 October 2023

Great quality, great advice over the phone, very fast delivery, all in all an absolutely fantastic service!!! Thank you!!!

Verified purchase. More information
Reviewed with 5 of 5

Martin Janisch 12 October 2023

Verified purchase. More information
Reviewed with 5 of 5

Anonym 8 October 2023

Not verified purchase. More information
Reviewed with 5 of 5

anonym September 17, 2023

everything ok - very fast delivery

Not verified purchase. More information
Reviewed with 5 of 5

Jens M. Stuttgart September 12, 2023

good advice and fast delivery. fits

Not verified purchase. More information
Reviewed with 5 of 5

Julian July 30, 2023

Great product. Every bearing ran without problems - no snagging or grinding. Highly recommended. Two of us were able to lay almost 49 square meters of tiles in one day.

Not verified purchase. More information
Reviewed with 5 of 5

Mike L., Klagenfurt June 26, 2023

fast delivery, friendly advice,

Not verified purchase. More information
René M June 24, 2023

very good – easy leveling – height fixing ring very practical

Not verified purchase. More information
Reviewed with 5 of 5

Tanja S., Steinberg 25 May 2023

TOP advice, shipping was super fast, TOP product. Installation was easy and we are completely satisfied. I would be happy to recommend it! You won't be disappointed.

Not verified purchase. More information
Reviewed with 5 of 5

Jochen L. Munich 18 May 2023

everything OK

Not verified purchase. More information
Reviewed with 5 of 5

Lutz M. Hamburg 17 May 2023

Gemeni is easy to work with. Very stable. Delivery was quick.

Not verified purchase. More information
Reviewed with 5 of 5

home builder 17 May 2023

Great system. I laid tiles on my terrace (18m2) in less than two days. Really good bearings, although I have no comparison. Completely sufficient for my needs.

Not verified purchase. More information
Reviewed with 5 of 5

Jochen M. Muenchen 17 May 2023

Price performance very good.

Not verified purchase. More information
Reviewed with 4 of 5

anonym 17 May 2023

Not verified purchase. More information
Reviewed with 5 of 5

Dirk 17 May 2023

Delivered quickly. Very good quality. But the package was heavy.

Not verified purchase. More information
Reviewed with 5 of 5

Holger 17 May 2023

as described.

Not verified purchase. More information
Reviewed with 5 of 5

Sven R. Bochum 17 May 2023

recommendation

Not verified purchase. More information
Reviewed with 5 of 5

anonym 17 May 2023

simply. top advice on the phone

Not verified purchase. More information
Reviewed with 4 of 5

anonym 17 May 2023

worked. product very good. delivery by DHL one day later than stated

Not verified purchase. More information
Reviewed with 5 of 5

anonym 17 May 2023

solid. top price

Not verified purchase. More information
Reviewed with 5 of 5

Gunter L. 17 May 2023

It was difficult at first but then it went quickly; even a layman could do it.

Not verified purchase. More information